All About Back and Neck Pain.com
TEXT SIZE Larger TextSmaller TextBOOKMARKBookmarkPRINTPrint
 

Braces

If you are diagnosed with a spinal disorder, deformity, or potential problem that can by helped through the use of external structural support, your physician may recommend the use of a neck or back brace. Neck and back braces are most often used to treat low back pain, trauma, infections, muscular weakness, neck conditions, and osteoporosis. They immobilize and support the spine when there is a condition that needs to be treated. Depending on the model that is used, they can put the spine in a neutral, upright, hyper-extended, flexed, or lateral-flexed position.

Spinal braces are used for a variety of reasons to control pain, lessen the chance of further injury, allow healing to take place, compensate for muscle weakness, and prevent or correct a deformity. They offer a safe, non-invasive way to prevent future problems or to help you heal from a current condition. Though the effects of bracing are primarily positive, they can lead to a loss of muscle function due to inactivity. Bracing can sometimes lead to psychological addiction, so that even when a person is healed and ready to be taken off the back brace, he or she feels dependent upon it for physical support.

The use of braces is widely accepted. They are effective tools in the treatment of spine disorders. In fact, more than 99% of orthopedic physicians advocate using them.

Braces are not new they have actually been around for centuries. Lumbosacral (lum-bo-sack-ral) corsets (for the lower back) were used as far back as 2000 B.C.! Bandage and splint braces were used in 500 A.D. to treat scoliosis. Recently, braces have become a popular way to help prevent primary and secondary lower back pain from ever occurring.

There are more than 30 types of back supports available for spine disorders. Some of the most common types are described below:

Neck Braces

Neck braces stabilize the cervical spine after neck surgery, trauma to the neck, or as an alternative to surgery. They are the type of spinal brace you most commonly see people wearing. There are several types available, including:

  • Soft Collar a flexible brace placed around the neck. It is typically used after a more rigid collar has been worn for the major healing. It is used as a transition to wearing no collar.
  • Philadelphia Collar a more rigid/stiff collar with front and back pieces that attach with Velcro on the sides. It is usually worn 24 hours a day until your physician instructs you to remove it. This collar is used for conditions such as a relatively stable cervical fracture, cervical fusion surgery, or a cervical strain. Another similar type is the Miami cervical brace.
  • Sterno-Occipital (stern-oh-ox-ip-ital) Mandibular(man-dib-you-lar) Immobilization Device (SOMI) a brace that holds your neck in a straight line that matches up with your spine. It offers rigid support to a damaged neck and prevents the head from moving around. With this brace, you are unable to bend or twist your neck. The restriction of motion helps the muscles and bones to heal from injury or surgery.
  • Halo a brace used to immobilize the head and neck. This is the most rigid of the cervical braces. It is only used after complex cervical spine surgery or if there is an unstable cervical fracture. The halo looks a lot like the word sounds. It has a metal ring (halo) that goes around your head and secures to your skull with four metal pins. The ring then attaches by four bars to a vest that is worn on your chest to bear the weight of the brace. The Halo is worn 24 hours a day until the spine injury heals.

Back Braces

  • Trochanteric (trow-can-ter-ick) Belt usually prescribed for sacroiliac joint pain or to stabilize pelvic fractures. The belt fits around the pelvis, between the trochanter (a bony portion below the neck of your thigh bone) and the iliac (pelvis) ridges or crests. The belt is about five to eight centimeters wide and buckles in front, just like a regular belt.
  • Lumbosacral (lum-bo-sack-ral) and Sacroiliac (sack-ro-ili-ack) Belt helps to stabilize the lower back. It is usually made of heavy cotton reinforced by lightweight stays. The pressure can be adjusted through laces on the side or back of the belt. Lumbosacral belts range in widths from 10 to 15 centimeters, and 20 to 30 centimeters. The sacroiliac belt is used to prevent motion by compressing the joints between the hipbone and sacrum at the base of the spine.
  • Corset provides rigid support for the back. Corsets vary in length. A short corset is typically used for low back pain, while a longer one is used for problems in the mid to lower thoracic spine. When people think of corsets, they usually conjure up images of women from earlier centuries who used them to make their waists look smaller. Today, in the treatment of back problems, corsets refer to a type of back brace that extends over the buttocks and is often held up by shoulder straps. Like the corsets of old, these corsets lace from the back, side, or front. There are metal stays that provide the appropriate rigidity and support for the back.
  • Rigid Brace usually prescribed for low back pain and spinal instability when standard back supports are not stiff enough. Rigid braces usually have upright pieces in the rear that curve to the shape of your lower spine and pelvis, with bands across the thoracic region of your spine. There are also fabric straps on the braces that provide pressure in the front. Some common types of rigid braces are:
    • Williams Brace a rigid brace with no vertical uprights in the middle, allowing you to bend.
    • Chair-back Brace a rigid brace that holds the lumbar spine in the neutral position and limits sideways and rotating movement of the lower spine.
    • Raney Flexion Jacket a rigid brace that reduces curvature of the lumbar spine by holding it in a neutral tilt.
  • Hyperextension Brace designed to prevent excessive bending. Hyperextension braces are often prescribed to treat frontal compression fractures that have occurred where the thoracic and lumbar areas of the spine meet. They can also be used after surgery for spinal fusion, taking pressure off the anterior or front of the thoracic vertebrae by restricting flexion (bending) of the thoracic and lumbar spine. Hyperextension braces have a front rectangular metal frame that puts pressure over the upper sternum or breast bone and the pubic bone, allowing the spine to extend. The brace also applies pressure over the T-10 level (the tenth vertebra in your thoracic spine). The hyperextension brace braces provides what is called "three-point stabilization" to the spine through a front abdominal pad, a chest pad, and a rear pad at the level of the fracture. The most common types of hyperextension braces are Knight Taylor and Jewett.
  • Molded Jacket designed to distribute pressure widely over a large area. It stabilizes the spine from the neck to the hips, distributing pressure evenly and taking excess pressure off overloaded or unstable areas. The molded jacket was originally made of plaster of Paris. Now it is usually made of molded plastic.
  • Lifting Belt designed to reduce low back strain and muscle fatigue that can occur when you are lifting heavy objects. It circles around your waist, covering the lumbar region of your spine, and closes in the front. Lifting belts are usually made of cloth or canvas and do not have stays. Some models also have lordosis pads to contour to the curvature of your spine.
 

SYMPTOMS ANALYZER

Before seeing your doctor, please complete the Symptoms Analyzer. This will help your physician determine your diagnosis and begin your steps toward recovery.

SYMPTOMS
 
 

FIND A SPINE SPECIALIST

Experienced professionals can help diagnose and treat your back and neck problems. Locate a professional in your area.

FIND